Structural Fire Damage Cleaning in Bithlo, FL
With the wallboard torn out, what is left is a skeleton of black studs, scorched rafters and smoke-stained block. Somebody now has to decide what gets blasted clean, what gets sistered and what gets replaced. Unify Fire Solutions connects you with independent, licensed and insured contractors in Bithlo who clean the framing, masonry and steel itself.
- Soda, dry ice and hand cleaning of framing
- Every stud and joist probed for char depth
- Sealer applied to lock in residual odor
Why the Bare Structure Needs Its Own Crew
Close up the walls over dirty framing and the smoke odor bleeds right back through the new finish. This stage decides whether your rebuilt rooms smell fresh or smell burned for years.
Licensed & Insured Independent Pros
Each contractor on our referral list is an independent, licensed and insured local company. Verify both, and ask whether the crew follows the IICRC S700 standard for fire and smoke work.
Upfront Written Estimates
Blasting is priced by surface area, media and access, and attics and crawlspaces cost more to reach. Get a written, itemized estimate in hand before any blasting begins.
Rapid Local Dispatch
A real person answers around the clock, and the search for a crew begins on that call. Timing depends on which crews near Bithlo are free, and it is often the same day.
Blasting Rigs and Probing Tools
Structural crews bring soda blast pots, dry ice units, big compressors, HEPA vacs, air scrubbers and a sharp awl to test every member.
Do not climb into a burned attic or walk a scorched roof deck to look for yourself. Weakened joists and burned-through sheathing can give way without warning, and exposed wiring may still be live. Let the crew confirm the structure will hold before anyone goes up, and keep everyone off the floor above a burned basement or crawlspace.
Structural Cleaning Services From Rafters to Slab
Furniture and debris are a separate job. This page is about the framing, masonry and steel that actually carry the load.
Char Depth Probing and Member Decisions
An awl pushed into a charred stud tells the story: if it stops in sound wood after a thin layer of char, the member is usually a cleaning candidate. Deep char that eats into the section of a joist or truss chord means sistering or replacement.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Sodium bicarbonate is softer than wood, so it strips soot and light char off studs, joists and roof decking without gouging the grain. Expect fine dust and residue that has to be contained and HEPA vacuumed when the blasting is done.
Dry Ice Blasting
Dry ice pellets hit the surface and turn straight into gas, so there is no media left behind to sweep up. It works well in tight attics and around wiring, though it costs more and is noisy.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
Small, isolated char spots are often handled by hand with wire brushes and sanders tied into a HEPA vacuum. Hand work is slower but sensible where a blast rig would be too much.
Brick, Block, Concrete and Steel Beams
Fireplace surrounds, block foundation walls and concrete slabs hold soot in their pores, and alkaline cleaners, scrubbing or blasting pull it out. Steel beams and columns are cleaned of soot and checked for warping or sag, which goes to the engineer.
Encapsulation and Attic Insulation Removal
Cleaned framing gets a coat of shellac-based or specialty encapsulant to lock in any odor left deep in the wood. In the attic, smoke-soaked blown-in or batt insulation is vacuumed out with a high-powered insulation vac before the rafters and decking are cleaned.
Crawlspaces get the same treatment on a smaller, dirtier scale: floor joists, sill plates and the underside of the subfloor are probed, blasted where needed and sealed. Expect a vapor barrier to be pulled and replaced if smoke or hose water soaked it.
Ask your contractor which method they recommend for each area and why. A good crew may soda blast the open walls, dry ice the attic around the wiring and hand sand a few studs near the panel.
Containment matters here, since blast media and loosened soot travel anywhere the air moves. The crew hangs poly over doorways, masks off the HVAC returns and runs air scrubbers under negative pressure while they work. Ask how they will protect finished rooms and windows that were not damaged.
Looking at Blackened Studs and Rafters?
Ring the dispatch line and we start finding a structural cleaning crew near Bithlo. It costs nothing to call.
Call +1-833-336-1630How a Structural Cleaning Job Unfolds
- 1
Phone the Dispatcher
Describe what is exposed: open stud walls, an attic, a crawlspace, block or steel. Mention if a roofer, engineer or adjuster has already been out.
- 2
Mobile Crew on Site
An independent crew shows up with its compressor, blast gear, poly and air scrubbers. They check that the roof and floor are safe to walk and that power to the open walls is off.
- 3
Probe, Mark and Quote
Every exposed member gets probed with an awl and marked clean, sister or replace, and anything borderline goes to a structural engineer. A written, itemized quote covering area, blast method, encapsulant and attic insulation comes before any work starts.
- 4
Blasting, Sealing and Walkthrough
After blasting and HEPA cleanup, the framing gets its sealer coat, and you walk the bare structure with the crew lead. Do a sniff test on a warm afternoon, and ask for photos of every marked member before the rebuild closes the walls.
Notes From People We Connected
The attic fire left every rafter black and the insulation soaked. They vacuumed out the insulation, dry iced the rafters around the wiring and sealed it all. An engineer looked at two deeply charred rafters and they were sistered instead of torn out.
I assumed every black stud in the hallway had to be replaced. The crew lead probed each one with an awl and showed me that most were just surface char. Soda blasting and a coat of sealer saved most of the wall.
The fire in our lower level left the block walls and the steel beam coated in soot. They scrubbed and blasted the block, cleaned the beam and had the engineer confirm it had not sagged. No smell now, even with the windows shut.
Common Questions About Cleaning Charred Framing
How do crews decide if a charred stud can stay?
They probe it. An awl or screwdriver pushed into the black surface shows how deep the char goes, and wood that is firm just under a thin crust can usually be blasted and sealed. Deep char, cracks or a reduced cross section mean sistering or replacement, with a structural engineer making the call on anything questionable.
What is the difference between soda blasting and dry ice blasting?
Soda media is mild on the grain and helps with odor, though it leaves a white dust that needs a full HEPA cleanup. Dry ice leaves no media behind and works well near wiring, but the equipment is noisy and the job usually costs more. Many crews use both on the same house.
Why seal the framing if it has already been cleaned?
Wood is porous, and smoke molecules sit deep in the grain where no blasting can reach. An encapsulating sealer traps what is left so the odor does not seep back through the finished walls. Sealing dirty wood does not work, so the cleaning has to come first.
Does the attic insulation have to come out after a fire?
In most cases where smoke got into the attic, it does. Loose-fill and batts act like a giant filter for smoke, and hose water often soaks them as well. It is vacuumed out with an insulation vac so the rafters and roof deck can be probed, blasted and sealed before anything new is blown in.
Can soot be cleaned off brick and concrete block?
Usually yes, though masonry takes more effort than drywall because soot sinks into the pores. Crews use alkaline masonry cleaners and stiff brushes, and soda or other media blasting for heavy buildup. Heat-cracked or spalled block and brick should be looked at by an engineer or mason.
Do I need a structural engineer for fire-damaged framing?
Not for every job, but for anything load-bearing that looks questionable, yes. Trusses, beams, headers, steel and heavily charred joists are where an engineer's letter protects you and helps the claim. Your local building department may also require one before the walls close.
Structural Fire Cleaning Throughout Bithlo
Our dispatch line covers Bithlo and the nearby communities around it, from older homes with plaster and solid-sawn joists to newer builds with engineered trusses. Attics, basements, crawlspaces, garages and light commercial spaces all come up regularly.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
Should the first contractor not suit you, ring us again and we will connect you with a different one. Get the bones cleaned before anyone hangs new drywall.
